top of page
Structural Repair
Resource Center
Technical articles, engineering insights, repair guides, and project highlights covering carbon fiber reinforcement, concrete repair, structural strengthening, and rehabilitation.


Ongoing third party testing plays an integral role in any structural reinforcement solution
Ongoing third party testing plays an integral role in any structural reinforcement solution that is relied upon to protect the safety of the community and the livelihoods of the professionals who install it. #structuralreinforcementsolutions #structuralrs #reinforcement #concreterepair #concretelife #concreteconstruction #engineered #carbonfiber #structuralengineering #foundationrepair #parkinggarage #stabilization #waterproofing #structuralengineers #structure #constructioni
Jan 24, 20201 min read
Carbon Fiber Strengthening systems that can perform like a Swiss Army knife
When we set out to develop our roll kits, one of the objectives we had in mind was to provide contractors with systems that had utmost versatility in the field without compromise. Unidirectional and Bidirectional Carbon Fiber can solve a vast spectrum of repairs. Each roll kit is designed to perform in the most demanding of applications - from beam and flexural strengthening to bowed wall stabilization. It was imperative to us that contractors could confidently install SRS co
Jan 14, 20201 min read


Bidirectional and Unidirectional Carbon Fiber working together
In this case, a combination of both bidirectional and unidirectional Carbon Fiber are being used to strengthen a block CMU wall. The SRS-660BI is used as a localized crack repair but also provides restraint between the vertical straps similar to a waler system. The SRS-660UNI vertical straps provide increased flexural strength over the entire height of the wall. #structuralstrengthening #structuralengineers #concreteconstruction #structuralengineering #concreterepair #conc
Jan 12, 20201 min read


CFRP column wrapping for increased load carry capacity
Load carrying capacity can be increased by wrapping columns horizontally. The strength added is similar what you get from the spiral or hoop rebar typically included in these columns. If the design load is being increased or if there is section loss in the existing reinforcing steel, CFRP can be used to remedy this situation and help prevent a compressive failure in the column. Other possible solutions to handle such situations are to add a reinforced concrete jacket or addi
Jan 10, 20201 min read


Crack repair to crawlspace footing using SRS-660BI Carbon Fiber
Horizontal cracks like this are usually the result of the reinforcing steel too close to the outer edge of the forms. When the forms are stripped, and if the conditions of the steel being hot on the day of the pour, a fine micro crack appears, concrete around the steel curing outwards meeting the normal curing of the concrete curing from the outside towards the middle. Then with seismic activity or maybe foundation settlement, the foundation bends a little, causing the crack
Jan 9, 20201 min read


Cracked and broken foundation corners
Cracked and broken foundation corners are a common issue where settlement has occurred in a homes foundation. These types of repairs are...
Jan 9, 20201 min read


Carbon Fiber column confinement for increased flexural capacity
Unidirectional Carbon Fiber Reinforced Polymer (CFRP), is frequently used for increasing flexural capacity of reinforced concrete columns subjected to bending and compression As we all know, concrete is great in compression but lacks the tensile properties necessary for the demands so is usually poured with steel rebar embedded in it. This rebar provides the necessary tensile requirements so that the concrete can perform for the intended application. If this rebar is missing
Jan 9, 20201 min read


What’s the difference in the SRS Carbon Fiber weaves? SRS-600UNI vs SRS-660BI
In the two fabrics offered by SRS, the SRS-600UNI and SRS-660BI, the UNI is short for unidirectional and BI is short for bidirectional. Unidirectional carbon fiber means all of the fibers run in the same direction. In the case of the SRS-600UNI the weave consists of and aerial weight of 600 grams of carbon fiber per square meter running the length of the roll. Bidirectional carbon fiber means that the fibers are running in two different directions. In the case of the SRS-66
Jan 7, 20205 min read


Concrete Column Repair
SRS-660BI Carbon Fiber is commonly used to wrap support columns or other structural components, adding a tensile capacity of 35,496 lbs per 12” When a column is wrapped with a bidirectional carbon fiber not only is the confining/load bearing strength of the column increased, but also the flexural strength of the column itself. As the fabric wraps the column it must lap back onto itself in order to achieve the necessary bond capacity to act as a continuous wrap. #structura
Jan 7, 20201 min read


Bowed Wall Stabilization using Unidirectional Carbon Fiber
Crossroads Foundation Repair was called out to a house in Brownsburg, Indianna to inspect a home where the basement walls were exhibiting some signs of horizontal and step cracking as well as bowing. Upon the completion of the inspection Kyle Leeman, Owner of Crossroads Foundation Repair, suggested the use of carbon fiber to reinforce the walls and prevent any further movement or damage. Kyle reached out to Structural Reinforcement Solutions, to obtain material for the repair
Jan 7, 20202 min read
bottom of page